• Easy to use
• Highly effective basic and intensive cleaning
• The soft fibres maintain protected surfaces without wear of treatment
• Also suitable for varnished, stone, plastic, PVC and other water resistant surfaces.
• Ideal for domestic and commercial use

• Coverage: Approximately 18 square metres per litre with one coat
• No of Coats:2
• Drying Time: 12 hours
• Sizes: 750ml, 2.5 litre and 10 litre

• Suitable for all exterior wood, including window shutters, cladding, fascias, pergolas, garden sheds and garden furniture
• Water based with drying time of 3-4 hours under normal climatic conditions
• Coverage approximately 12 square metres per litre on dressed timber. Less on rough sawn/textured timbers
• Can be applied by brush, microfibre roller or microfibre fleece. Also suitable for spraying.
• Normally only one coat renovation is required.

• Based on natural plant oils, organic oxides and pigments
• Low VOC’s. Product contains a maximum of 400 grams per litre of a mild solvent. (De-aromatised, benzene free, pharmaceutical grade white spirit)
• Base and top coat in one product – no primer required.
• Transparent finish means wood grain remains visible
• Highly water and dirt resistant
• Reduces wood swelling and shrinkage
• Microporous breathable finish which does not crack, peel or flake
• Approximately 26 square metres per litre coverage on medium density timbers. Coverage will be less on softwoods or band sawn timbers such as Western Red Cedarf

• Coverage: Approximately 26 square metres per litre with one coat
• No of coats: 2
• Drying time: 8 – 10 hours
• Sizes: 125ml, 750ml and 2.5 litres

• Base and top coat in one finish
• Fast drying
• Transparent finish means wood grain remains visible
• Highly water and dirt resistant
• Reduces wood swelling and shrinkage
• Microporous breathable finish which does not crack, peel or flake
• In a lot of cases, sanding will not be necessary before recoating.

• Exterior use only
• Coverage: Up to 26 square metres per litre per coat. On softwoods such as cedar and pine, coverage will be less.
• No of coats: 2 is normal, however 3 may be needed on soft absorbent timbers such as cedar
• Drying time: 4 – 6 hours
• Sizes: 5ml sample sachets, 750ml and 2.5 litres
• Natural Oil Woodstain colours vary in weather and UV resistance.

• The darker colours containing more pigments have better weather and UV resistance than light colours.
• Lighter colours such as White 900 and Pearl Grey 906 have less weather and UV resistance than darker colours.
• Woodstain Clear Matt 701 has no UV resistance. See notes below.

• Coverage: Approximately 20 square metres per litre on new hardwoods. Much less on old dry softwoods
• No of Coats: 2 on new timber; 1 for recoat
• Drying time: 12 hours
• Sizes: 750ml and 2.5 litres. Some colours are available in 10 litres

Not suitable for use on horizontal surfaces such as timber decks.

The microporous surface allows the wood to breathe, thereby reducing swelling and shrinkage. The finish helps to slow the greying process on vertical surfaces.

The finish contains biocides, which are active ingredients helping to prevent mould, algae and fungal attack. As such, they should not be used internally, or externally on tables etc where food may be eaten, or timber decking which will be walked upon.

Available in 7 lightly tinted colour tones. A 2 coat application (or possibly 3 thin coats for softwoods or timbers in full exposed conditions). With the strength of the UV in New Zealand, the treated surface should be inspected regularly for fading, and maintenance undertaken where required. In most situations, the finish will last 12-18 months before recoat is required. Recoat is easy. Generally, a wash down and clean is all that is needed, followed by one rejuvenation coat once the timber is dry. Where the timber has been left to grey off, the wood will need rejuvenation with a product such as Osmo’s Wood Reviver Power Gel.

Note: UV Protection Oil Natural 429 is optimally balanced with white pigments to retain the natural character of light coloured timbers such as pine and oak. It is not recommended for use on darker timbers such as kwila or jarrah etc, as the white pigment may give the timber a chalky appearance. Applied to timber in full exposure, UV Natural will last approximately 4-6 months before recoat is required.

In all cases a trial test to determine suitability is recommended.

• Very water and dirt resistant
• Reduces wood swelling and shrinkage
• Resists growth of algae and mildew and resists fungal attack
• Microporous, breathable finish which does not crack, peel, flake or blister
• No sanding necessary for future applications
• Coverage: Approximately 18 square metres per litre with one coat
• No. of coats: 2
• Application temperature: +5°C to 35°C
• Drying time:  12 hours
• Sizes: 750ml and 2.5 litres.

• Coverage: Approximately 18 square metres per litre with one coat
• No of Coats:2
• Drying Time: 12 hours
• Sizes: 750ml, 2.5 litre and 10 litre

• Coverage: Approximately 30 square metres per litre per coat depending on timber density.
• No of coats: 1 or 2
• Drying time: Approx 8-12 hours
• Sizes: 500ml, 1 litre and 2.5 litres